Choice Vintners

Wine Cellars Cooling Systems ( Climatech )

Climatech Dual Digital Controller

Price: 225/each (USD)

Climatech Dual Digital Controller

* Integrates seamlessly with the Climatech
* Programmed to optimal settings for your Climatech
* Easy to read LCD backlit display
* Scratch resistant touch screen controls
* Precise and accurate control, within +/-1°
* Easy installation and set-up

Price: $225.00

Climatech Ducting Kits

Price: /each (USD)

The Climatech Wine Cooling System is designed to be completely adaptable for many types of wine cellar scenarios. The unique design allows for both through-wall and remote installation. High powered fans in the unit allow cellar air to be ducted both into and from the cellar, and exhaust air to be ducted out from the unit.
Price: Vary by size / Shipping $15.00

Climatech Electric Heater

Price: /each (USD)

Nothing can affect the proper climate conditions in a wine cellar like cold temperatures. The Climatech cooling system is designed to work under extreme conditions. The Climatech Electric Heater keeps your cellar at a constant temperature, optimal for wine storage, even as the ambient temperature drops as the unit is designed to heat from 40° F.
Price: $595.00 / Shipping $40.00

Climatech Humidification Attachment

Price: /each (USD)

Climatech Wine Cooling System Accessories

Climatech Humidification Attachment

The key to the success of any wine cellar is the ability to control humidity as well as temperature. A wine cellar constructed solely with temperature control is only doing half the job. The unique design of the Climatech wine cellar cooling unit makes adding humidity to your cellar easy.

Price: $1095.00 (2 ton)
Shipping: $

Climatech Humidification Attachment

Price: /each (USD)

Climatech Low Ambient Protection

Price: /each (USD)

A low ambient kit will help protect your Climatech cooling system when it is exposed to temperatures below 40° F. The low ambient kit warms the compressor and allows the system to continue its normal function.
Price: $340.00 / Shipping $40.00

Climatech Water Cooled Option

Price: /each (USD)

The water-cooled Climatech uses a lot of water and is not recommended when connecting to well water or public utilities. The best application is for the use in high rise apartment complexes, restaurants or country clubs that have cooling towers or chiller systems that can be tied into for water. The water typically gets re-circulated throughout the chiller/cooling tower whereas water from a well or public utilities is drained away.
Price: $500.00
Shipping & Handling: $

Climatech Wine Cooling Systems Model Number: 15000

Price: /each (USD)

Model 15000

The fully ducted Climatech wine cooling system is simply the finest cooling system ever designed for wine room environments. Its flexible design offers customers many different installation options and once installed, provides the most reliable and efficient wine room climate control.
• Provides "invisible" fully ducted cooling with remote installation
• Requires no HVAC technician – can be installed by your contractor
• Features an optional in-line humidification system
• Boasts a flawless performance record
Features & Benefits
• Aluminum outer body is lightweight and corrosion resistant, providing protection from the elements.
• The Climatech is a commercial grade unit, but offers ultra quiet climate control for your wine cellar.
• The design of the Climatech wine cellar cooling system provides multi-panel access for easy service.
• ETL listed and approved. Learn more about ETL approval at www.etl.com.
• Unlike any other unit, the Climatech comes standard with high pressure static fans. These fans allow you to use extended lengths of ductwork.
• System can be installed inside of an attic. (Considerations need to be made for temperature and ducting the exhaust air out of the space.)

Dimensions (width x depth x height): 43” x 22 ” x 18”

Performance
Nominal Tonnage: 2 tons
Nominal Compressor: 2.5 HP
Net Cooling Capacity*
@ 70° F Ambient: 16200 / 17750 BTUH
@ 80° F Ambient: 15200 / 16650 BTUH
@ 90° F Ambient: 14100 / 15350 BTUH
Net Cooling Volume: 4001 - 8400 Cu. Ft.

Control: Room mounted non-programmable thermostat
Accuracy: ± 2°F

Evaporator
Fan Motor Size: 240 Watts
Rated Air Flow: 740 CFM
Air Flow with 25’ flex duct: 715 CFM

Condenser
Fan Size: 240 Watts
Rated Air Flow: 750 CFM
Air flow with 25’ flex duct: 720 CFM

Heat: Integral electric heater coil
Capacity: 2000 / 6826 Watt / BTUH
Temperature rise - including fan: 8.1 Deg° F

Humidifier: Removable drip pad with integral fan
Supply water temp of 60 Deg F: 1.6 gal./day
Supply water temp of 90 Deg F: 3.5 gal./day
Supply water temp of 120 Deg F: 5.1 gal./day
Control : Cellar mounted digital humidistat

Electrical Requirements
Power Requirements: 230/1/60 V/P/H
Current Draw - Cooling mode: 16 Amps
Current Draw - Heating mode: 10 Amps
Minimum Circuit Size: 20 Amps
Optional Low Ambient: 0.2 Amps
Optional Humidifier: 0.2 Amps

Cabinet
Construction: .063 Aluminum
Finish: Black, Powder Coat, Corrosion Inhibiting
Weight: 195 lbs
Dimensions (inches)
Length: 39
Width: 22
Height: 14

Condensate Drain 0.5" ID

1. Net cooling capacity at cellar temp. & humidity of 55° F & 60 % RH / 60° F & 60% RH and at rated airflow. Reduce capacity by 3% for each 10% reduction in either condenser or evaporator airflow, 5% for both.
2. Vigilant, Inc. reserves the right to make changes to this document without prior notice at its sole discretion.
3. All ratings recorded at sea level.

Recommended Insulated Flexible Ductwork Sizing
Evaporator (cooling) Coil 12”; Inlet (return air) Single 12”; Outlet (supply air) Double 10”; Condenser (heat rejection) Coil 12”; Inlet Single 12”; Outlet Double 10”

Notes: Do not exceed a total of 25' for each length of ductwork run
1. The above referenced sizes are internal diameter in inches.
2. If a single supply is used out of the unit but then splits into two (2) ducts, the above size recommended for double is used after the split.
=================================
Model: 15000
Capacity: 2 ton
BTU's: 15,200
Electrical : 2230v/1ph/60hz
Cu. Ft.: 4001-8400
Dimensions: 43" x 22" x 18"
[103.2 x 52.8 x 43.2 cm]
Price: $5,995
Shipping: $250

Climatech Wine Cooling Systems Model Number: 3000

Price: /each (USD)

The fully ducted Climatech wine cooling system is simply the finest cooling system ever designed for wine room environments. Its flexible design offers customers many different installation options and once installed, provides the most reliable and efficient wine room climate control.
• Provides "invisible" fully ducted cooling with remote installation
• Requires no HVAC technician – can be installed by your contractor
• Features an optional in-line humidification system
• Boasts a flawless performance record
Features & Benefits
• Aluminum outer body is lightweight and corrosion resistant, providing protection from the elements.
• The Climatech is a commercial grade unit, but offers ultra quiet climate control for your wine cellar.
• The design of the Climatech wine cellar cooling system provides multi-panel access for easy service.
• ETL listed and approved. Learn more about ETL approval at www.etl.com.
• Unlike any other unit, the Climatech comes standard with high pressure static fans. These fans allow you to use extended lengths of ductwork.
• System can be installed inside of an attic. (Considerations need to be made for temperature and ducting the exhaust air out of the space.)

Dimensions (width x depth x height) 35” x 14” x 14”

Performance:
Nominal Tonnage: 1/4 Ton
Nominal Compressor: 1/3HP
Net Cooling Capacity*:
@ 70° F Ambient: 3300 / 3650 BTUH
@ 80° F Ambient 3000 / 3300 BTUH
@ 90° F Ambient 2800 / 3050 BTUH
Net Cooling Volume: < 800 Cu. Ft.

Controls: Room mounted non-programmable thermostat
Accuracy: ± 2°F

Evaporator :
Fan Motor Size: 75 Watts
Rated Air Flow: 235 CFM
Air Flow with 25’ flex duct 207 CFM

Condenser :
Fan Size: 75 Watts
Rated Air Flow: 253 CFM
Air flow with 25’ flex duct: 220 CFM

Heat
Type: Integral electric heater coil
Capacity: 1000 / 3413 Watt / BTUH
Temperature rise - including fan: 13.5 Deg° F

Humidifier: Removable drip pad with integral fan
Supply water temp of 60 Deg F: 1.6 gal./day
Supply water temp of 90 Deg F: 3.5 gal./day
Supply water temp of 120 Deg F: 5.1 gal./day
Control: Cellar mounted digital humidistat

Electrical Requirements
Power Requirements: 115/1/60 V/P/H
Current Draw - Cooling mode: 8.6 Amps
Current Draw - Heating mode: 9.4 Amps
Minimum Circuit Size:15 Amps
Optional Low Ambient: 0.4 Amps
Optional Humidifier: 0.3 Amps

Cabinet
Construction: .063 Aluminum
Finish: Black, Powder Coat, Corrosion Inhibiting
Weight: 80 lbs
Dimensions (inches) Length: 35
Width: 14
Height: 14

Condensate Drain: 0.5” ID

1. Net cooling capacity at cellar temp. & humidity of 55° F & 60 % RH / 60° F & 60% RH and at rated airflow. Reduce capacity by 3% for each 10% reduction in either condenser or evaporator airflow, 5% for both.
2. Vigilant, Inc. reserves the right to make changes to this document without prior notice at its sole discretion.
3. All ratings recorded at sea level.

Recommended Insulated Flexible Ductwork:
Evaporator (cooling) Coil: 8”; Inlet (return air) Single 8”; Outlet (supply air) Double 6”;
Condenser (heat rejection) Coil: 8”, Inlet Single 8”; Outlet Double 6”

Notes: Do not exceed a total of 25' for each length of ductwork run
1. The above referenced sizes are internal diameter in inches.
2. If a single supply is used out of the unit but then splits into two (2) ducts, the above size recommended for double is used after the split.

=========================================

Model: 3000
Capacity: 1/4 ton
BTU's: 3000
Electrical : 115v/1ph/60hz
Cu. Ft.: <800
Dimensions: 35" x 14" x 14"
[84 x 33.6 x 33.6 cm]
Price: $3,195
Shipping: $150

Climatech Wine Cooling Systems Model Number: 5000

Price: /each (USD)

Model 5000

The fully ducted Climatech wine cooling system is simply the finest cooling system ever designed for wine room environments. Its flexible design offers customers many different installation options and once installed, provides the most reliable and efficient wine room climate control.
• Provides "invisible" fully ducted cooling with remote installation
• Requires no HVAC technician – can be installed by your contractor
• Features an optional in-line humidification system
• Boasts a flawless performance record
Features & Benefits
• Aluminum outer body is lightweight and corrosion resistant, providing protection from the elements.
• The Climatech is a commercial grade unit, but offers ultra quiet climate control for your wine cellar.
• The design of the Climatech wine cellar cooling system provides multi-panel access for easy service.
• ETL listed and approved. Learn more about ETL approval at www.etl.com.
• Unlike any other unit, the Climatech comes standard with high pressure static fans. These fans allow you to use extended lengths of ductwork.
• System can be installed inside of an attic. (Considerations need to be made for temperature and ducting the exhaust air out of the space.)

Dimensions (width x depth x height): 39” x 22 ” x 14”

Performance:
Nominal Tonnage: 1/2 ton
Nominal Compressor: 1/2 HP
Net Cooling Capacity*: @ 70° F Ambient: 5600 / 6050 BTUH
@ 80° F Ambient: 5300 / 5700 BTUH
@ 90° F Ambient: 4850 / 5275 BTUH
Net Cooling Volume: 801-1800 Cu. Ft.

Controls: Room mounted non-programmable thermostat
Accuracy: ± 2°F

Evaporator
Fan Motor Size: 100 Watts
Rated Air Flow: 435 CFM
Air Flow with 25’ flex duct: CFM 400

Condenser
Fan Size: 100 Watts
Rated Air Flow: 400 CFM
Air flow with 25’ flex duct: 365 CFM

Heat: Integral electric heater coil
Capacity: 1000 / 3413 Watt / BTUH
Temperature rise - including fan: 8.6 Deg° F

Humidifier: Removable drip pad with integral fan
Supply water temp of 60 Deg F: 1.6 gal/day
Supply water temp of 90 Deg F: 3.6 gal/day
Supply water temp of 120 Deg F: 5.1 gal/day
Control: Cellar mounted digital humidistat

Electrical Requirements: 115/1/60 V/P/H
Current Draw - Cooling mode: 11.9 Amps
Current Draw - Heating mode: 9.6 Amps
Minimum Circuit Size: 15 Amps
Optional Low Ambient: 0.4 Amps
Optional Humidifier: 0.3 Amps

Cabinet Construction: .063 Aluminum
Finish: Black, Powder Coat, Corrosion Inhibiting
Weight: 125 lbs
Dimensions (inches): Length: 39
Width: 22
Height: 14
Condensate Drain: 0.5" ID

1. Net cooling capacity at cellar temp. & humidity of 55° F & 60 % RH / 60° F & 60% RH and at rated airflow. Reduce capacity by 3% for each 10% reduction in either condenser or evaporator airflow, 5% for both.
2. Vigilant, Inc. reserves the right to make changes to this document without prior notice at its sole discretion.
3. All ratings recorded at sea level.

Recommended Insulated Flexible Ductwork Sizing
Evaporator (cooling) Coil 10” Inlet (return air) Single 10”; Outlet (supply air) Double 6”
Condenser (heat rejection) Coil 10”, Inlet Single 10”;Outlet Double 6”

Notes: Do not exceed a total of 25' for each length of ductwork run
1. The above referenced sizes are internal diameter in inches.
2. If a single supply is used out of the unit but then splits into two (2) ducts, the above size recommended for double is used after the split.

Model: 5000
Capacity: 1/2 ton
BTU's: 5300
Electrical : 115v/1ph/60hz
Cu. Ft.: 801-1800
Dimensions: 39" x 22" x 14"
[93.6 x 52.8 x 33.6 cm]
Price: $3,950
Shipping: $150

Climatech Wine Cooling Systems Model Number: 8000

Price: /each (USD)

Model 8000

The fully ducted Climatech wine cooling system is simply the finest cooling system ever designed for wine room environments. Its flexible design offers customers many different installation options and once installed, provides the most reliable and efficient wine room climate control.
• Provides "invisible" fully ducted cooling with remote installation
• Requires no HVAC technician – can be installed by your contractor
• Features an optional in-line humidification system
• Boasts a flawless performance record
Features & Benefits
• Aluminum outer body is lightweight and corrosion resistant, providing protection from the elements.
• The Climatech is a commercial grade unit, but offers ultra quiet climate control for your wine cellar.
• The design of the Climatech wine cellar cooling system provides multi-panel access for easy service.
• ETL listed and approved. Learn more about ETL approval at www.etl.com.
• Unlike any other unit, the Climatech comes standard with high pressure static fans. These fans allow you to use extended lengths of ductwork.
• System can be installed inside of an attic. (Considerations need to be made for temperature and ducting the exhaust air out of the space.)

Dimensions (width x depth x height): 39” x 22 ” x 14”

Performance
Nominal Tonnage: 1 Ton
Nominal Compressor: 1 HP
Net Cooling Capacity*
@ 70° F Ambient: 8400 / 9100 BTUH
@ 80° F Ambient: 7800 / 8450 BTUH
@ 90° F Ambient: 7300 / 7900 BTUH
Net Cooling Volume: 1801 - 4000 Cu. Ft.

Controls: Room mounted non-programmable thermostat
Accuracy: ± 2°F
Evaporator:
Fan Motor Size: 195 Watts
Rated Air Flow: 510 CFM
Air Flow with 25’ flex duct: 485 CFM

Condenser
Fan Size: 195 Watts
Rated Air Flow: 500 CFM
Air flow with 25’ flex duct: 475 CFM

Heat: Integral electric heater coil
Capacity: 2000 / 6826 Watt / BTUH
Temperature rise - including fan: 12 Deg° F

Humidifier: Removable drip pad with integral fan
Supply water temp of 60 Deg F: 1.6 gal./day
Supply water temp of 90 Deg F: 3.5 gal./day
Supply water temp of 120 Deg F: 5.1 gal./day
Control: Cellar mounted digital humidistat

Electrical Requirements
Power Requirements: 230/1/60 V/P/H
Current Draw - Cooling mode: 9.0 Amps
Current Draw - Heating mode: 9.6 Amps
Minimum Circuit Size: 15 Amps
Optional Low Ambient: 0.2 Amps
Optional Humidifier: 0.2 Amps

Cabinet
Construction .063 Aluminum
Finish: Black, Powder Coat, Corrosion Inhibiting
Weight: 145 lbs
Dimensions (inches) Length 39
Width 22
Height 14

Condensate Drain 0.5" ID

1. Net cooling capacity at cellar temp. & humidity of 55° F & 60 % RH / 60° F & 60% RH and at rated airflow. Reduce capacity by 3% for each 10% reduction in either condenser or evaporator airflow, 5% for both.
2. Vigilant, Inc. reserves the right to make changes to this document without prior notice at its sole discretion.
3. All ratings recorded at sea level.

Recommended Insulated Flexible Ductwork Sizing:
Evaporator (cooling) Coil 10”, Inlet (return air) Single 10”; Outlet (supply air) Double 8”; Condenser (heat rejection) Coil 10” Inlet Single 10”; Outlet Double 8”

Notes: Do not exceed a total of 25' for each length of ductwork run
1. The above referenced sizes are internal diameter in inches.
2. If a single supply is used out of the unit but then splits into two (2) ducts, the above size recommended for double is used after the split.
=======================
Model: 8000
Capacity: 1 ton
BTU's: 7800
Electrical : 230v/1ph/60hz
Cu. Ft.: 1801-4000
Dimensions: 39" x 22" x 14"
[93.6 x 52.8 x 33.6 cm]
Price: $4,550
Shipping: $200